sonosax同期设备
SX-BD1
单路控制台尤其适用于同期挑杆
适用范围：采访，报导等等
主要特征：
高品质话筒放大器
幻象电源供电于话筒
输入增益选择（+20dB,+46dB,+72dB）低切
配置了与其它sonosax产品一样的限幅器
耳机监听有三种选择
电平由旋钮控制
12LED电平显示
输出兼容各种设备（DAT，调音台，摄像机，MD，无线等等）
内置千周
仅由4节7号电池供电
这款新型设备，录音师可根据录音要求随意放置，此设备可配shoeps 话筒和sonosax M4话筒.
适用范围：采访，报导等等
主要特征：
高品质话筒放大器
幻象电源供电于话筒
输入增益选择（+20dB,+46dB,+72dB）低切
配置了与其它sonosax产品一样的限幅器
耳机监听有三种选择
电平由旋钮控制
12LED电平显示
输出兼容各种设备（DAT，调音台，摄像机，MD，无线等等）
内置千周
仅由4节7号电池供电
这款新型设备，录音师可根据录音要求随意放置，此设备可配shoeps 话筒和sonosax M4话筒.
SX-M32
3轨调音台
LED表,前面板输入增抑为无极
主RL输出编组输出
单声道输出(MONO输出)
3个输入带返回电平调节
数字输出AES/EBU输出
通道1-2输出可MS link
输入可立体声返回
数字输出可达到24bit/192KHz
176*44/138(MM)
重:800g
5号电池或外置6-15V供电
LED表,前面板输入增抑为无极
主RL输出编组输出
单声道输出(MONO输出)
3个输入带返回电平调节
数字输出AES/EBU输出
通道1-2输出可MS link
输入可立体声返回
数字输出可达到24bit/192KHz
176*44/138(MM)
重:800g
5号电池或外置6-15V供电
SX-R4
录音机
8轨硬盘或CF卡录音机
正面板输入增抑两档控制
立体声LINK
八通道AES(四卡侬)输入
2个线路输入
每通道有限幅器时间码
视频跟随0.1%(N制)
不平衡立体声线路输出
176*44/138(MM)
重:800g
5号电池或外置6-15V供电
8轨硬盘或CF卡录音机
正面板输入增抑两档控制
立体声LINK
八通道AES(四卡侬)输入
2个线路输入
每通道有限幅器时间码
视频跟随0.1%(N制)
不平衡立体声线路输出
176*44/138(MM)
重:800g
5号电池或外置6-15V供电
SX-M2
专业立体声话筒/线路放大器
可与任何机器相连，如DAT，MD，DV，miniDV录音机，开盘机
话筒由48伏供电
2节9V电池供电或Ni-Cd 供电
外部供电：12V-24V
尺寸：5,75" x 3,4" x 1,6" (146 x 85 x 40mm)
重量： 435g含电池
输入：
类型：平衡转换，卡侬插头
阻抗：5k Ohms , 20Hz to 20kHz
增益：76dB to 20dB (高), 40dB to 6dB (低), 0dB (中)
低切：18dB/oct, -3dB at 70Hz
过载显示：6dB before clipping level
话筒供电：48V幻象供电
输出：XLR平衡
非平衡3.5英寸立体声插头
可与任何机器相连，如DAT，MD，DV，miniDV录音机，开盘机
话筒由48伏供电
2节9V电池供电或Ni-Cd 供电
外部供电：12V-24V
尺寸：5,75" x 3,4" x 1,6" (146 x 85 x 40mm)
重量： 435g含电池
输入：
类型：平衡转换，卡侬插头
阻抗：5k Ohms , 20Hz to 20kHz
增益：76dB to 20dB (高), 40dB to 6dB (低), 0dB (中)
低切：18dB/oct, -3dB at 70Hz
过载显示：6dB before clipping level
话筒供电：48V幻象供电
输出：XLR平衡
非平衡3.5英寸立体声插头
SX42
4路输入2路输出ENG/EFP调音台
低耗电量 4 节 1.5V 7号电池
NiCd 或 NiMH 电池能达到 : 10 to 15 hours 或12V DC
平衡输出输入
根据IP45制作的防水旋转推子
每一通道带有话筒放大器及48V供电
M/S解码器在1-2和3-4通道上
两个输出带有限幅器
此调音台在最恶劣的环境下使用最少10年以上，外部所有零件是防水的
选配件：
均衡器（可加在1，2通道上），数模转换器
尺寸: 10.2" (260 mm) x 6.2" (160 mm) x 1.9" (50 mm)
重量: 2.1 kg带电池
适用温度范围 : -40°F (-40°C) to 140° F (60° C)
低耗电量 4 节 1.5V 7号电池
NiCd 或 NiMH 电池能达到 : 10 to 15 hours 或12V DC
平衡输出输入
根据IP45制作的防水旋转推子
每一通道带有话筒放大器及48V供电
M/S解码器在1-2和3-4通道上
两个输出带有限幅器
此调音台在最恶劣的环境下使用最少10年以上，外部所有零件是防水的
选配件：
均衡器（可加在1，2通道上），数模转换器
尺寸: 10.2" (260 mm) x 6.2" (160 mm) x 1.9" (50 mm)
重量: 2.1 kg带电池
适用温度范围 : -40°F (-40°C) to 140° F (60° C)
SX-62R
KEY FEATURES
Electronically balanced Mic/Line Input, XLR connectors
48V Phantom for Mic power
Pre LF Cut for rough wind conditions - PAD - Phase reversal
Input trim on the front panel for easy Mic Gain adjustment, retractable
Sweep LF Cut, retractable
Mix routing by PAN Pot
Stereo and MS linking of channel 1/2 - 3/4 and 5/6
M/S Decoder
PFL for rapid channel monitoring
Limiter on each channel
Stereo AUX Input assignable to the MIX or to Track 7&8
Electronically balanced Mic/Line Input, XLR connectors
48V Phantom for Mic power
Pre LF Cut for rough wind conditions - PAD - Phase reversal
Input trim on the front panel for easy Mic Gain adjustment, retractable
Sweep LF Cut, retractable
Mix routing by PAN Pot
Stereo and MS linking of channel 1/2 - 3/4 and 5/6
M/S Decoder
PFL for rapid channel monitoring
Limiter on each channel
Stereo AUX Input assignable to the MIX or to Track 7&8
SX-ES64
6 Mic/Line input channels with high quality, low noise, transformer-less microphone preamplifier
- 48V Phantom power, phase reversal
- Up to 80dB of Gain.
- Sweep Low Frequency Cut, 15 to 400Hz at 18dB per octave
- Direct channel output, electronically balanced, internally selectable Pre-EQ, Post EQ or Post fader
- Sonosax's well acclaimed Limiter on each channel with adjustable threshold level
- Led Peak-Meter on each channel
- 4 Mix busses, assignable Pre, Post Fader or Off
- High quality,smooth and robust 100mm Linear Fader
- Optional 3 bands semi-parametric EQ ( HF – sweep MF – LF )- 4 Main Output electronically balanced on XLR's,
- Retractable rotary Master Fader
- Built-in Slate Microphone and Ref Tone Oscillator, individually assignable to the Mix busses
- Two independent Monitoring system with M/S decoding and Private Line for duplex communication
- 4 Return Lines, assignable to monitoring and/or mix busses for re-injection
- Choice of multiway connector for Camera Send/Return ( such as Hirose, Tajimi, etc )- Optional 8 ways high quality A/D Converter for the 6 direct out and for Main 1/2, 48 & 96kHz at 24 bits
- DC Powered 6 to 18VDC, either from an external DC Source, Main adapter or internal batteries ( 4x D-Cells )
- Low power consumption
- 48V Phantom power, phase reversal
- Up to 80dB of Gain.
- Sweep Low Frequency Cut, 15 to 400Hz at 18dB per octave
- Direct channel output, electronically balanced, internally selectable Pre-EQ, Post EQ or Post fader
- Sonosax's well acclaimed Limiter on each channel with adjustable threshold level
- Led Peak-Meter on each channel
- 4 Mix busses, assignable Pre, Post Fader or Off
- High quality,smooth and robust 100mm Linear Fader
- Optional 3 bands semi-parametric EQ ( HF – sweep MF – LF )- 4 Main Output electronically balanced on XLR's,
- Retractable rotary Master Fader
- Built-in Slate Microphone and Ref Tone Oscillator, individually assignable to the Mix busses
- Two independent Monitoring system with M/S decoding and Private Line for duplex communication
- 4 Return Lines, assignable to monitoring and/or mix busses for re-injection
- Choice of multiway connector for Camera Send/Return ( such as Hirose, Tajimi, etc )- Optional 8 ways high quality A/D Converter for the 6 direct out and for Main 1/2, 48 & 96kHz at 24 bits
- DC Powered 6 to 18VDC, either from an external DC Source, Main adapter or internal batteries ( 4x D-Cells )
- Low power consumption
SX-ST
SX-VT
- Compact and fully modular construction
- Un-compromised choice of components
- Ultra-low noise mic preamps with +48V phantom power available on all input channels
- Electronically balanced, transformer less inputs and outputs
- Wide bandwidth10Hz to 200kHz, suitable for SACD and next converters generations
- High dynamic range and large headroom
- Direct Outputs selectable Pre-EQ, Post-EQ or Post Fader
- 8 Groups individually selectable Pre or Post Pan
- 4 Auxiliaries individually selectable Pre or Post Fader
- Limiter on each input channel
- High quality conductive plastic linear fader
- Dual peak meters on each input for Pre and Post Fader level indications
- Triple Monitoring section with 2 Private Lines for communications
- Large scale level-meter indicators switch able to level and phase correlation meter
- Internal 8 channels of high quality A to D converter ( optional )
- Integrated 8 track Hard disk and Compact flash Card recorder ( optional )
- Compact size and low weight
- Low consumption
SX-PR
An ingenious feature of this modular system is its adaptability to right or left-handed users. The master module with the modulometer may be installed on either side of the mixer.
Like all other SONOSAX manufactures instruments, SX-PR has been built using only professional components (conductive plastic potentiometers, switches and connectors with goldplated contacts, etc.) to ensure unparalleled levels of quality, performance and reliability. In addition, the switches and potentiometers are air-tight and thus dust protected.
MINIR82
Status
The MINIR82 status is shown by means of the Green or Red "status" led's and the screen
display. The following status scenarios are possible:
RECORD READY
the Red LED is flashing, the MINIR82 is ready to start recording.
RECORDING
the Red LED lights On steady, confirming that a recording is in progress
PLAYING
the Green LED lights On steady, a Take is playing
PLAY PAUSE
the Green LED flashes, indicating that the loaded Take is actually paused.
PLAY STOP.
A Take is loaded ready to be played, no LED lights on, nor flashes
Clipping LEDs
The "Left Channel" and "Right Channel" Led's shows two particular statuses that are either:
Limiters: either the Left or the Right LED lights On independently when the Microphone
Input signal reaches a level of 2.5dB before clipping, thus activating the Limiter.
Clipping: the Input signal is too high on the microphone A/D Converter, both Left and
Right LED's light On together
SX-XD4
- Optional "Fully Discrete" ultra low noise microphone preamplifier
- up to 80dB of Gain.
- Pre LF-Cut ( the LF-Cut is located before the mic-preamplifier )
- Sonosax well acclaimed Limiter with adjustable threshold level
- Channels linking for Stereo mic, M/S pair, Dual M/S, 4 channels Soundfield B-Format
- Moving coil Peak-Meter with 44dB of balistics
- Balanced Analog Line Out- High Quality high stability A/D Converter, 24/16 bits 44,1 up to 192 kHz sampling rate
- 2 xAES on XLR3 pin, 2 x SPDIF on RCA and 2x Optical outputs for Mic channels 1-2 & 3-4
- WorldClock Sync In & Out- Optional Mutifunction Card with Digital I/O and multiple Sync facilities ( Ethernet-Video-Time Code etc) made by Merging Technologies- Dual Monitoring system with individual selector and volume control, Mono -Stereo and M/S modes
- Analog stereo return and Digital stereo return, AES, SPDIF, Optical 16/24bits 44,1 up to192kHz- DC Powered 12 to 18VDC, either from an external Main adapter or batteries
FD-M4
This system, using Fully Discrete technology, is incredible.
For certain applications, such as fixed distribution or public address systems, we also created the PA-M4. This card is a simplified version with only two gain possibilities: unity gain and +10 or +20dB gain (user selectable).
These three cards and different variations are compatible, and the user can chose between these basic alternatives, mixing different cards in the same system.
FD-A100
SONOSAX FD-A100 is the most compact professional stereo amplifier created to date. This unit has 2 inputs per channel, namely 1 floating balanced input with an XLR connector and one unbalanced input with a cinch connector. In this manner, this monitoring amplifier can be connected with any source and has the advantage of being extremely practical and flexible. The output connectors take cables up to a section of 10mm2 and offer optimal contact. A limiter, which can be disconnected, wards off any deterioration of loudspeakers by clipping.
As regards the electronics of SONOSAX FD-A100, only transistors are used for sound processing, to ensure the absence of coloration, harmonic and transient distortion. All components are of professional type, as for all SONOSAX products, such as conductive plastic potentiometers, hermetic switches with gold-plated contacts, gold-plated connectors, to ensure a long life.
Despite its small size, FD-A100 compares favourably with the best amplifiers on the market, for quality of sound.
SX-S
The SONOSAX SX-S Series is a line of extemely compact, portable, self-contained mixing consoles, designed for professional mobile and studio applications.Built in a strong, rugged, anodized aluminium case, the SONOSAX SX-S Series provides the best solution whenever performance, versatility and small size are important.The SONOSAX SX-S Series is manufactured with no compromise on quality:
- Penny and Giles linear faders (83mm travel)
- Gold connectors and military type componants
- Sealed conductive plastic rotary switches
| SX-S6: | up to 6 channels |
| SX-S8: | up to 8 channels |
| SX-S10: | up to 10 channels |
SX-T
Due to its versatility, the SONOSAX SX-T is the ideal choice for numerous applications, such as: fixed and mobile recording studio and broadcast
video, television and cinema production and post production
digital or analogic sound recording, in 2 or multi-track
very high quality sound systems for concert halls, theaters, etc.
STELLADAT II
2 and 4 tracks on tape
44,1 / 48 / 88,2 / 96kHz sampling rate
True 4 channels audio mixer
2 to 3 hours autonomy with Lithium Ion battery
Advanced modes (Chase, Remote) and functions (Jog, Shuttle, etc.)
SMPTE and Aaton Time Code
STELLADAT II is the unique 2 and 4 tracks DAT portable tape recorder.
While other manufacturers are making their DAT machines cheaper rather than better, SONOSAX has been working to achieve manufacturing efficiencies while providing a better product with more features. STELLADAT II maintains of course the standard of quality and dependability that customers have learned to expect from Swiss manufacturers.